牌号简介 About |
---|
Nucrel® AE是乙烯、甲基丙烯酸和丙烯酸酯的三元共聚物。它可用于传统的挤出涂料,共挤涂料和挤出层压设备设计加工聚乙烯树脂。它可用作约20%至40%Nucrel® AE与80%至60%低密度聚乙烯的混合物中聚乙烯的改性剂,以增强箔的粘合性能。粘合力的改善程度取决于加工条件。包装非侵蚀性食品和其他非食品产品的含箔袋和袋。小吃结构其他箔、金属化膜或纸涂层,用作热密封或连接层 Nucrel® AE is a terpolymer of ethylene, methacrylic acid, and acrylate. It is available for use in conventional extrusion coating, coextrusion coating and extrusion laminating equipment designed to process polyethylene resins. It can be used as a modifier for PE in blends of approximately 20 to 40% Nucrel® AE with 80 to 60% LDPE for enhancement of foil adhesion properties. The level of adhesion improvement depends on processing conditions. Foil-containing pouches and sachets for packaging non-aggressive food and miscellaneous non-food products. Snack structures Other foil, metallized film, or paper coatings as a heat seal or tie layer |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
0.920 | g/cm³ | ASTM D792 |
密度 Density |
0.920 | g/cm³ | ISO 1183 |
熔体质量流动速率 Melt Flow Rate |
|||
190℃,2.16kg 190℃,2.16kg |
11 | g/10min | ISO 1133 |
190℃,2.16kg 190℃,2.16kg |
11 | g/10min | ASTM D1238 |
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
维卡软化温度 Vicat Softening Temp |
79.0 | ℃ | ASTM D1525 |
维卡软化温度 Vicat Softening Temp |
℃ | ISO 306 | |
熔融峰值温度 Melting peak temperature |
℃ | ASTM D3418 | |
熔融温度 Melting temperature |
|||
DSC DSC |
℃ | ISO 3146 | |
冰点 freezing point |
℃ | ASTM D3418 |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
【新闻资讯】查看全部
降低注塑机螺杆磨损水平需要留意的几个方面
2018-01-11 注塑机螺杆长时间在高温、高压、高机械扭力及高磨擦环境下进行工作,前几个因素是工艺条件所需,而磨擦造成的损耗则不可避免。 一般螺杆都进行过表面氮化处理,以提高表面硬度,亦即提高抗磨损能力。但是如果忽略了引起磨损的原因,不设法将磨损尽量降低,必然会大大降低螺杆的工作寿命。 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |