ALKAMIX™ MB-PA505
含氟聚合物 & 澳大利亚凯诺斯
ALKAMIX™ MB-6006
含氟聚合物 & 澳大利亚凯诺斯
牌号信息 |
含氟聚合物 & 澳大利亚凯诺斯 指导价格:暂无 塑料库存: 缺货 |
含氟聚合物 & 澳大利亚凯诺斯 指导价格:暂无 塑料库存: 缺货 |
|
牌号简介 |
ALKAMIX™ MB-PA505是基于2%浓度的含氟聚合物化合物的加工助剂母粒。在挤出过程中,可在线性低密度聚乙烯(LLDPE)中添加ALKAMIX™ MB-PA505,以消除熔融断裂(“Sharkskin”)型挤出缺陷。所需的添加量将根据挤压设备和所用LLDPE的类型而变化,但建议的添加量在1%到3%之间。ALKAMIX™ MB-PA505与“Alkatuff”膜聚合物中使用的工艺助剂相容。当添加到不含任何其他添加剂的聚乙烯配方中时,基于良好制造实践并确保符合美国食品和药品管理局法规CFR21要求的最大添加量为10%。转换器必须对使用该材料作为部件制造的成品的适用性以及对给定限制的遵守情况进行验证,以确保符合所有相关法规。整体迁移限制可适用于成品。 ALKAMIX™ MB-PA505 is a processing aid masterbatch based on a fluoropolymer compound at a concentration of 2 percent. ALKAMIX™ MB-PA505 can be added to linear low density polyethylene (LLDPE) during extrusion to eliminate melt fracture ("Sharkskin") type extrusion defects. The level required will vary according to extrusion equipment and type of LLDPE being used, however the recommended addition level is between 1 and 3 percent. ALKAMIX MB-PA505 is compatible with the process aid used in "Alkatuff" film polymers. The maximum level of addition of ALKAMIX™MB-PA505 based on both good manufacturing practice and to ensure conformance to the requirements to the United States Food and Drug Administration Regulations CFR21 is 10 percent, when added to a polyethylene formulation free of any other additives. The suitability of finished articles manufactured using this material as a component, and the observance of given limitations, must be verified by the converter for each application to ensure compliance with all relevant regulations. An overall migration limit may apply to the finished article. |
ALKAMIX™ MB-6006是基于浓度为5%的含氟聚合物化合物的加工助剂母粒。在挤出过程中,可在线性低密度聚乙烯(LLDPE)中添加ALKAMIX™ MB-6006,以消除熔融断裂(“Sharkskin”)型挤出缺陷。所需的添加量将根据挤压设备和所用LLDPE的类型而变化,但建议的添加量在1%到2%之间。Alkamix MB6006与“Alkatuff”薄膜聚合物中使用的工艺助剂兼容。当添加到不含任何其他添加剂的聚乙烯配方中时,根据良好的生产实践和确保符合美国食品药品管理局法规CFR21要求的最大添加量为4%。转换器必须对使用该材料作为部件制造的成品的适用性以及对给定限制的遵守情况进行验证,以确保符合所有相关法规。整体迁移限制可适用于成品。 ALKAMIX™ MB-6006 is a processing aid masterbatch based on a fluoropolymer compound at a concentration of 5 percent. ALKAMIX™ MB-6006 can be added to linear low density polyethylene (LLDPE) during extrusion to eliminate melt fracture ("Sharkskin") type extrusion defects. The level required will vary according to extrusion equipment and type of LLDPE being used, however the recommended addition level is between 1 and 2 percent. ALKAMIX MB6006 is compatible with the process aid used in "Alkatuff" film polymers. The maximum level of addition of ALKAMIX™MB-6006 based on both good manufacturing practice and to ensure conformance to the requirements to the United States Food and Drug Administration Regulations CFR21 is 4 percent, when added to a polyethylene formulation free of any other additives. The suitability of finished articles manufactured using this material as a component, and the observance of given limitations, must be verified by the converter for each application to ensure compliance with all relevant regulations. An overall migration limit may apply to the finished article. |
|
产品描述 | |||
厂家: | 澳大利亚凯诺斯 Qenos | 澳大利亚凯诺斯 Qenos | |
类别: | 含氟聚合物 含氟聚合物 | 含氟聚合物 含氟聚合物 | |
填料: | |||
用途: | 母料 | 母料 | |
性能特点: | |||
加工条件: |
备注 |
1 一般属性:这些不能被视为规格。
|
1 一般属性:这些不能被视为规格。
|
价格走势对比图
含氟聚合物 ALKAMIX™ MB-PA505
含氟聚合物 ALKAMIX™ MB-6006
型号 | 类别 | 厂家 | 产地 | 颜色 | 首期使用量 | 后期使用量 | 包装 | 交期 | 成型产品 | 操作 |
---|---|---|---|---|---|---|---|---|---|---|
GP-525N | GPPS | VATAA土耳其地区 | 亚太地区 | 天 |
单据状态:未提交