牌号简介 About |
---|
可发泡树脂。密度降低10%时的所有性能;0.250厚试样。 Foamable resin. All properties at 10% density reduction; 0.250" thick test specimens. |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
|||
-- -- 3 |
0.998 | g/cm³ | |
-- -- |
1.11 | g/cm³ | |
收缩率 Shrinkage rate |
|||
MD:6.4 mm MD:6.4 mm |
0.60 到 0.80 | % | 内部方法 |
吸水率 Water absorption rate |
|||
24hr 24hr |
0.060 | % | ASTM D570 |
室外适用性 Outdoor applicability |
f2 | UL 746C | |
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
拉伸强度 tensile strength |
|||
屈服,6.35 mm Yield, 6.35 mm |
MPa | ||
断裂,6.35 mm Fracture, 6.35 mm |
MPa | ||
拉伸应变 Tensile strain |
|||
屈服,6.35 mm Yield, 6.35 mm |
% | ||
断裂,6.35 mm Fracture, 6.35 mm |
% | ||
弯曲模量 Bending modulus |
|||
6.40 mm 6.40 mm |
MPa | ASTM D790 | |
弯曲强度 bending strength |
|||
屈服,6.40 mm Yield, 6.40 mm |
MPa | ASTM D790 | |
冲击性能 IMPACT |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
悬臂梁无缺口冲击强度 Notched impact strength of cantilever beam |
|||
23℃,6.4 mm 23℃,6.4 mm |
J/m | ASTM D4812 | |
装有测量仪表的落镖冲击 Dart impact equipped with measuring instruments |
|||
23℃,Energy at Peak 23℃,Energy at Peak |
J | ASTM D3763 | |
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
热变形温度 Hot deformation temperature |
|||
0.45 MPa,未退火,6.4 mm 0.45 MPa, unannealed, 6.4 mm |
℃ | ||
1.8 MPa,未退火,6.4 mm 1.8 MPa, unannealed, 6.4 mm |
℃ | ||
相对温度指数 Relative temperature index |
℃ | UL 746 | |
电气性能 Electrical performance |
℃ | UL 746 | |
冲击机械性能 Impact mechanical performance |
℃ | UL 746 | |
电气性能 Electrical performance |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
耐电弧性 Arc resistance 4 |
ASTM D495 | ||
相比漏电起痕指数 Compared to the leakage tracing index |
UL 746 | ||
高电弧燃烧指数(HAI) High Arc Burning Index (HAI) 5 |
UL 746 | ||
高电压电弧起痕速率 High voltage arc marking rate |
|||
HVTR HVTR |
UL 746 | ||
热丝引燃 Hot wire ignition |
|||
HWI HWI |
UL 746 | ||
阻燃性能 FLAME CHARACTERISTICS |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
阻燃等级 Flame retardant level |
|||
3.00 mm 3.00 mm |
|||
4.70 mm 4.70 mm |
|||
Flame Class Minimum Density(Foam) Flame Class Minimum Density(Foam) |
g/cm³ | ||
辐射板 Listing Radiation Plate Listing 6 |
|||
补充信息 Supplementary information |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
Weight Reduction Weight Reduction |
|||
Foam - Impact:6.40 mm Foam - Impact:6.40 mm |
% | ||
Foam - Mechanical:6.40 mm Foam - Mechanical:6.40 mm |
% | ||
Foam - Physical:6.40 mm Foam - Physical:6.40 mm |
% | ||
Foam - Thermal:6.40 mm Foam - Thermal:6.40 mm |
% |
备注 |
---|
3. Foam Molded |
4. 钨电极 |
5. Surface |
6. UL Tested |
【新闻资讯】查看全部
影响模具抛光效果的要素
2016-07-13 影响模具抛光效果,主要有以下三个因素: 一、具钢的质量 表面硬度不均匀或特性上有差异往往会产生抛光困难,钢材中的各种夹杂物和气孔都不利于抛光。 二、热处理工艺 热处理在很多方面会影响到抛光性能,表面硬化钢材由于表面碳成分增加,其细微组织不利于抛光。因为钢材表面的小氧化物颗粒增加使抛光困难。钢材表面的渗碳或者脱碳都会使硬度发生变化,造成抛光上的困难。 三、抛光技术及工艺设备 不同硬度对抛光工艺的影 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |