牌号简介 About |
---|
BC 7062是一种充铝、低粘度的环氧树脂大体积铸造树脂。这些室温固化系统允许用户选择厚度为1/8英寸至最大6英寸,无起泡或产生过度收缩。铸造厚度可通过加入铝针、泡沫或颗粒来增加。BC 7062经过适当的固化后,可提供近乎完美的复制效果,从而形成尺寸稳定、坚硬、坚硬的表面。用于构建重复模型、原型、模型、面模等。 BC 7062 are aluminum filled, low viscosity epoxy mass casting resins. These room temperature cure systems allow the user choice thicknesses of 1/8 inch to a maximum of 6 inches without foaming or yielding excessive shrinkage. Casting thicknesses may be increased by incorporating aluminum needles, puffs or granules. BC 7062, when properly cured, provides nearly perfect reproduction, resulting in a dimensionally stable, hard, tough surface. For use in constructing duplicate models, prototypes, patterns, facing dies, etc. |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
1.85 | g/cm³ | |
收缩率 Shrinkage rate |
|||
MD MD |
0.12 | % | ASTM D2566 |
Uncured Properties Uncured Properties |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
重量混合比(PBW) Weight Mix Ratio (PBW) |
|||
Resin Resin |
12 | ||
Hardener Hardener |
1.0 | ||
体积混合比(PBV) Volume Mixing Ratio (PBV) |
|||
Resin Resin |
6.5 | ||
粘度 viscosity 2 |
|||
布络克菲尔德,24℃ Brookfield, 24 ℃ 2 |
Pa·s | ||
固化时间 Curing time |
|||
24℃ 24℃ |
hr | ||
储存稳定性 storage stability |
|||
24 ℃ 24 ℃ |
min | ||
Cured Properties Cured Properties |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
邵氏硬度 Shore hardness |
|||
邵氏 D,24℃ Shaw's D, 24 ℃ |
|||
拉伸断裂强度 Tensile fracture strength |
MPa | ||
弯曲断裂强度 Bending fracture strength |
MPa | ||
压缩强度 compressive strength |
MPa | ||
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
线性热膨胀系数 Linear coefficient of thermal expansion |
|||
MD MD |
1/℃ | ||
热变形温度 Hot deformation temperature |
℃ | ||
脱模时间 stripping time |
min |
备注 |
---|
2、Mixed |
【新闻资讯】查看全部
美油收盘大涨1.2%,突破70美元关口!创下两年半新高
2021-06-09 搜料网资讯: 原油期货价格周二收盘上涨,原因是市场预计美国的能源需求将会进一步改善。据最近的一项调查显示,主要产油国贯彻了逐步增加产量的计划。与此同时,交易员还在权 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |