牌号简介 About |
---|
Ensinger Industries推出了新一代xray不透明xro系列热塑性塑料,并与Tecason xro合作。在彩色PPSU挤压棒的标准线中增加了一个无线电遮光器,用于骨科尺寸试验和其他仪器设备,允许在荧光透视和X光透视上清晰显示组件。这适应了微创和图像引导手术带来的一些新挑战。Tecasonp xro已经按照IS0 10993的要求进行了测试,用于与组织、骨骼和牙本质接触不到24小时的外部通信设备。这些试验包括:最大化/致敏试验、细胞毒性、皮内试验、急性全身毒性试验和溶血试验。TECASON™ P XRO的设计允许在微创和图像引导手术期间在荧光透视和X光透视上清晰可见仪器。从而为用户提供特殊的好处。 Ensinger Industries launches its new line of xray opaque, XRO series, thermoplastic shapes with TECASON™P XRO. A radio opacifer is added to the standard line of colored PPSU extruded rod for orthopedic sizing trials and other instrument devices allowing for clear visibility of the component on fluoroscopy and xray.This accommodates some of the new challenges created by minimally invasive and image guided surgery. TECASON™P XRO has been tested to the requirements of IS0 10993 for external communication devices intended for less than 24 hour contact with tissue, bone and dentin. These tes tsinclude: Maximization / Sensitization Testing, Cytotoxicity, Intracutaneous Test, Acute Systemic Toxicity Test and the Hemolysis Test. TECASON™ P XRO has been formulated to allow clear visibility of an instrument on fluoroscopy and xray during minimally invasive and image guided surgery. Thus providing an exceptional benefit to the user. |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
1.30 | g/cm³ | ASTM D792 |
吸水率 Water absorption rate |
|||
23℃,24hr 23℃,24hr |
0.33 | % | ASTM D570 |
冲击性能 IMPACT |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
悬臂梁缺口冲击强度 Impact strength of cantilever beam notch |
|||
23℃ 23℃ |
210 | J/m | ASTM D256 |
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
洛氏硬度 Rockwell hardness |
|||
R 级 R-level |
123 | ASTM D785 | |
拉伸模量 Tensile modulus |
2000 | MPa | ASTM D638 |
拉伸强度 tensile strength |
|||
屈服,23℃ Yield, 23 ℃ |
MPa | ASTM D638 | |
拉伸应变 Tensile strain |
|||
断裂,23℃ Fracture, 23 ℃ |
% | ASTM D638 | |
弯曲模量 Bending modulus |
|||
23℃ 23℃ |
MPa | ASTM D790 | |
弯曲强度 bending strength |
|||
23℃ 23℃ |
MPa | ASTM D790 |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
【新闻资讯】查看全部
注塑机液压零碎泄漏缘由及处理
2018-01-15 一、总概述 泄漏是注塑机普遍存在的故障现象,主要是由于液体在液压元件和管路中流动时产生压力差及各元件存在间隙等引起泄漏。振业注塑汇另外,恶劣工况条件也会对注塑机的密封产生一定的影响。液压系统一旦发生泄漏,将会引起系统压力建立不起来,液压油泄漏还会造成环境污染,影响生产甚至产生无法估计的严重后果。下面针对一些影响注塑机液压系统泄漏的因素来简单的谈一下其泄漏原因及对策。 二、泄漏的分类 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |