牌号简介 About |
---|
产品说明环氧树脂模塑料,无组织填充,玻璃纤维增强,高耐热性,良好的电气性能,即使在较高的温度下,极轻微的后收缩,增加的介质阻力,UL列出的模塑料1.5 mm/hb(bk)应用领域电气零件,热,化学和机械受压零件,例如接线板、线轴、汽车电子设备、反光镜、火花塞接头 Product Description Epoxy moulding compound, inorganically filled, glass fibre reinforced, highly heat resistant, good electrical properties, even at higher temperatures, very slight post shrinkage, increased media resistance, UL listed moulding compound 1.5 mm / HB (BK) Application Areas Electrical parts, thermally, chemically and mechanically stressed parts, e.g. terminal boards, bobbins, car electronics, reflectors, spark plug connectors |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
1.85 | g/cm³ | ISO 1183 |
表观密度 Apparent density |
0.80 | g/cm³ | ISO 60 |
收缩率 Shrinkage rate 3 |
0.35 | % | ISO 2577 |
吸水率 Water absorption rate |
|||
23℃,24hr 23℃,24hr |
13.0 | mg | ISO 62 |
后收缩 Post contraction 3 |
0.050 | % | ISO 2577 |
冲击性能 IMPACT |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
简支梁缺口冲击强度 Charpy Notched Impact Strength |
|||
23℃ 23℃ |
kJ/m² | ISO 179/1eA | |
简支梁无缺口冲击强度 Charpy Unnotch Impact strength |
|||
23℃ 23℃ |
kJ/m² | ISO 179/1eU | |
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
热变形温度 Hot deformation temperature |
|||
8.0 MPa,未退火 8.0 MPa, unannealed |
℃ | ISO 75-2/C | |
电气性能 Electrical performance |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
表面电阻率 Surface resistivity |
ohms | IEC 60093 | |
体积电阻率 Volume resistivity |
ohms·cm | IEC 60093 | |
介电强度 Dielectric strength 5 |
|||
1 mm 1 mm 5 |
kV/mm | IEC 60243-1 | |
相对电容率 Relative permittivity |
|||
100 Hz 100 Hz |
IEC 60250 | ||
耗散因数 Dissipation factor |
|||
100 Hz 100 Hz |
IEC 60250 | ||
阻燃性能 FLAME CHARACTERISTICS |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
1.50 mm,黑色 1.50 mm, black |
UL 94 | ||
补充信息 Supplementary information |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
压缩成型压力 Compression molding pressure |
MPa | ||
压缩成型温度 Compression molding temperature |
℃ | ||
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
球压硬度 Ball hardness |
|||
H 961/30 H 961/30 |
MPa | ISO 2039-1 | |
拉伸模量 Tensile modulus |
MPa | ISO 527-1-2 | |
拉伸强度 tensile strength |
MPa | ISO 527-2/5 | |
弯曲模量 Bending modulus |
MPa | ISO 178 | |
弯曲强度 bending strength 4 |
MPa | ISO 178 | |
压缩强度 compressive strength |
MPa | ISO 604 |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
2 Injection |
3 0.079 in/min |
4 short term, electrode layout P25mm/P25mm in transformer oil equivalent to IEC 60296 |
【新闻资讯】查看全部
CAE分析生产连接器元件的回流变构成绩
2018-07-20 宝理塑料株式会社(Polyplastics Co., Ltd.,以下简称宝理塑料)近期成功地采用计算机辅助工程(CAE)来分析采用液晶聚合物(liquid crystal polymer,简称LCP)生产连接器元件的回流变形问题。 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |