牌号简介 About |
---|
成型参数:建议4小时用于高拉伸强度和光滑表面处理,或真空金属化。16小时的干燥温度为180°F。对于两区机器,后部温度为600-650°F,前部温度为580-620°F。 Molding Parameters: 4 hours recommended for high tensile strength and smooth surface finish, or for vacuum metalizing. The dry temperature at 16 hours is 180°F. For 2-zone machines, the rear temperature is 600-650°F, and the front temperature is 580-620°F. |
产品描述 Product Description
加工条件:注射成型 Injection Molding
性能特点: 防火阻燃等级V-0; 机械强度好; 尺寸稳定性好; 耐疲劳性好; 防火阻燃等级V-2; 耐高温; 韧性好; Good Rigidity,Good flexibility,Good Dimensional Stability,High Heat Resistance,Fatigue resistance,V-2,V-0
填料:玻璃纤维/玻璃珠 10
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
1.28 | g/cm³ | ASTM D792 |
收缩率 Shrinkage rate |
|||
MD:3.2 mm MD:3.2 mm |
0.30 | % | ASTM D955 |
吸水率 Water absorption rate |
|||
24hr 24hr |
0.13 | % | ASTM D570 |
冲击性能 IMPACT |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
悬臂梁缺口冲击强度 Impact strength of cantilever beam notch |
|||
23℃,6.4mm 23℃,6.4mm |
96 | J/m | ASTM D256 |
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
热变形温度 Hot deformation temperature |
|||
1.8 MPa,未退火 1.8 MPa, unannealed |
141 | ℃ | ASTM D648 |
0.45 MPa,未退火 0.45 MPa, unannealed |
℃ | ASTM D648 | |
相对温度指数 Relative temperature index |
|||
电气性能 Electrical performance |
UL 746 | ||
1.5 mm 1.5 mm |
℃ | UL 746 | |
强度机械性能 Strength mechanical performance |
UL 746 | ||
冲击机械性能 Impact mechanical performance |
UL 746 | ||
3.0 mm 3.0 mm |
℃ | UL 746 | |
阻燃性能 FLAME CHARACTERISTICS |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
阻燃等级 Flame retardant level |
UL 94 | ||
1.50 mm 1.50 mm |
UL 94 | ||
3.00 mm 3.00 mm |
UL 94 | ||
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
拉伸模量 Tensile modulus |
|||
23℃ 23℃ |
MPa | ASTM D638 | |
拉伸强度 tensile strength |
|||
断裂,23℃ Fracture, 23 ℃ |
MPa | ASTM D638 | |
拉伸应变 Tensile strain |
|||
断裂,23℃ Fracture, 23 ℃ |
% | ASTM D638 | |
弯曲模量 Bending modulus |
|||
23℃ 23℃ |
MPa | ASTM D790 | |
弯曲强度 bending strength |
|||
断裂,23℃ Fracture, 23 ℃ |
MPa | ASTM D790 | |
洛氏硬度 Rockwell hardness |
|||
M 级 M-level |
ASTM D785 |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
【新闻资讯】查看全部
烟台公布首批产业领军人才 道恩股份刘晓平名列其中
2021-06-17 搜料网资讯: 日前,烟台市委办公室、市政府办公室公布首批烟台市产业领军人才名单, 道恩 股份技术总监刘晓平榜上有名。据悉,刘晓平是龙口市唯一一名入选战略性 新兴 产业的领 |