牌号简介 About |
---|
Vydyne® 25WSP是一种黑色耐候注塑成型级PA66树脂。该树脂具有强度高、刚性好、韧性好、熔点高、表面润滑性好、耐磨性好等工程性能的良好平衡组合。Vydyne® 25WSP保持了PA66对许多化学品、机器和机油、溶剂和汽油的典型耐化学性。耐候性是通过在PA66基体中加入分散良好的细颗粒炭黑而获得的。虽然炭黑的存在通常会增加脆性,但这种树脂的配方是为了尽量减少延展性的损失,如延伸率和伊兆冲击强度。因此,与其他黑色、耐候、无冲击改性的PA66模制品相比,25WSP模制品经常表现出更高的延展性和实用韧性。Vydyne® 25WSP树脂是内部和外部润滑,以改善机器饲料和特殊的模具释放。Vydyne® 25WSP用于高生产率应用。在许多应用中,由于模件可以在较高温度下从型腔中移除,因此可以缩短成型周期。在零件容易粘在型腔中的困难模具中,Vydyne® 25WSP可以减少或消除模具释放喷剂的需要。在常规生产基础上实施较短的成型周期之前,应根据规范检查关键的成型零件尺寸。典型应用/最终用途:机器进料和模具释放润滑,Vydyne® 25WSP提供了非常好的流动性和易成型性。典型应用包括电缆扎带/扎带,其中其易于流动、良好延展性和高拉伸强度的组合尤其具有吸引力,以及各种需要耐候性的电气/电子和其他应用。 Vydyne 25WSP is a black, weather-resistant injection-molding grade PA66 resin. This resin offers a well-balanced combination of engineering properties characterized by high strength, rigidity, good toughness, high melt point, good surface lubricity and abrasion resistance. Vydyne 25WSP maintains the chemical resistance typical of PA66 to many chemicals, machine and motor oils, solvents and gasoline. Weather resistance is obtained by incorporating finely divided, well-dispersed carbon black particles in the PA66 matrix. While the presence of carbon black usually increases brittleness, this resin has been formulated to minimize loss of ductility properties such as elongation and Izod impact strength. As a result, parts molded from 25WSP frequently exhibit higher ductility and practical toughness compared with other black, weather-resistant, non-impact-modified PA66 molded parts. Vydyne 25WSP resin is internally and externally lubricated for improved machine feed and exceptional mold release. Vydyne 25WSP is intended for use in high-productivity applications. In many applications, the molding cycle can be reduced because molded parts may be removed from the cavity at higher temperatures. In difficult molds where parts have a tendency to stick in the cavity, Vydyne 25WSP can reduce or eliminate the need for mold release sprays. Critical molded part dimensions should be checked against specifications before implementing shorter molding cycles on a routine production basis. Typical Applications/End Uses: Lubricated for machine feed and mold release, Vydyne 25WSP provides very good flow and easy moldability. Typical applications include cable ties/tie straps, where its combination of easy flow, good ductility and high tensile strength is particularly attractive, and a wide variety of electrical/electronic and miscellaneous applications requiring weather resistance. |
产品描述 Product Description
厂家:美国奥升德 Ascend
类别:PA66 PA66
用途:电气/电子应用领域;
颜色:黑色
加工条件:注射成型 Injection Molding
性能特点: 耐磨; 耐汽油; 耐化学性; 防火阻燃等级V-2; 润滑性; 机械强度好-延展; 易流动; 耐候抗UV; 拉伸性能好; 机械强度好; 耐油; 含脱模剂; 韧性好; Good Rigidity,Weather resistance is good,Good flexibility,Ductility,Good liquidity,Good stripping performance,Lubricating,Good Tensile Strength,Good wear resistance,Grease resistance,Solvent resistance,Gasoline resistance,V-2
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
1.14 | g/cm³ | ISO 1183 |
收缩率 Shrinkage rate |
ISO 294-4 | ||
TD:23℃,2.0 mm TD:23℃,2.0 mm |
1.4 | % | ISO 294-4 |
MD:23℃,2.0 mm MD:23℃,2.0 mm |
1.6 | % | ISO 294-4 |
吸水率 Water absorption rate |
|||
平衡,23℃,50% RH Equilibrium, 23 ℃, 50% RH |
2.4 | % | ISO 62 |
23℃,24hr 23℃,24hr |
1.2 | % | ISO 62 |
耐候性 Weathering resistance |
UL 746C | ||
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
拉伸模量 Tensile modulus |
|||
23℃ 23℃ |
MPa | ISO 527-2 | |
拉伸强度 tensile strength |
|||
屈服,23℃ Yield, 23 ℃ |
MPa | ISO 527-2 | |
拉伸应变 Tensile strain |
|||
屈服,23℃ Yield, 23 ℃ |
% | ISO 527-2 | |
标称拉伸断裂应变 Nominal tensile fracture strain |
|||
23℃ 23℃ |
% | ISO 527-2 | |
弯曲模量 Bending modulus |
|||
23℃ 23℃ |
MPa | ISO 178 | |
弯曲强度 bending strength |
|||
23℃ 23℃ |
MPa | ISO 178 | |
23℃ 23℃ |
MPa | ISO 178 | |
泊松比 Poisson's ratio |
ISO 527-2 | ||
冲击性能 IMPACT |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
简支梁缺口冲击强度 Charpy Notched Impact Strength |
ISO 179/1eA | ||
-30℃ -30℃ |
kJ/m² | ISO 179/1eA | |
23℃ 23℃ |
kJ/m² | ISO 179/1eA | |
简支梁无缺口冲击强度 Charpy Unnotch Impact strength |
ISO 179/1eU | ||
-30℃ -30℃ |
ISO 179/1eU | ||
23℃ 23℃ |
ISO 179/1eU | ||
悬臂梁缺口冲击强度 Impact strength of cantilever beam notch |
|||
23℃ 23℃ |
kJ/m² | ISO 180 | |
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
热变形温度 Hot deformation temperature |
|||
1.8 MPa,未退火 1.8 MPa, unannealed |
℃ | ISO 75-2/A | |
0.45 MPa,未退火 0.45 MPa, unannealed |
℃ | ISO 75-2/B | |
熔融温度 Melting temperature |
℃ | ISO 11357-3 | |
线性热膨胀系数 Linear coefficient of thermal expansion |
|||
TD:23~55℃,2 mm TD:23~55℃,2 mm |
1/℃ | ISO 11359-2 | |
MD:23~55℃,2 mm MD:23~55℃,2 mm |
1/℃ | ISO 11359-2 | |
相对温度指数 Relative temperature index |
|||
电气性能 Electrical performance |
UL 746 | ||
0.75 mm 0.75 mm |
℃ | UL 746 | |
1.5 mm 1.5 mm |
℃ | UL 746 | |
3.0 mm 3.0 mm |
℃ | UL 746 | |
强度机械性能 Strength mechanical performance |
UL 746 | ||
0.75 mm 0.75 mm |
℃ | UL 746 | |
1.5 mm 1.5 mm |
℃ | UL 746 | |
3.0 mm 3.0 mm |
℃ | UL 746 | |
冲击机械性能 Impact mechanical performance |
UL 746 | ||
0.75 mm 0.75 mm |
℃ | UL 746 | |
1.5 mm 1.5 mm |
℃ | UL 746 | |
3.0 mm 3.0 mm |
℃ | UL 746 | |
电气性能 Electrical performance |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
介电强度 Dielectric strength |
|||
1 mm 1 mm |
kV/mm | IEC 60243 | |
耐电弧性 Arc resistance |
|||
3.0 mm 3.0 mm |
ASTM D495 | ||
相比漏电起痕指数 Compared to the leakage tracing index |
|||
3.00 mm 3.00 mm |
V | IEC 60112 | |
高电弧燃烧指数(HAI) High Arc Burning Index (HAI) |
UL 746 | ||
0.75 mm 0.75 mm |
UL 746 | ||
1.5 mm 1.5 mm |
UL 746 | ||
3.0 mm 3.0 mm |
UL 746 | ||
高电压电弧起痕速率 High voltage arc marking rate |
|||
HVTR HVTR |
UL 746 | ||
热丝引燃 Hot wire ignition |
|||
HWI HWI |
UL 746 | ||
0.75 mm 0.75 mm |
UL 746 | ||
1.5 mm 1.5 mm |
UL 746 | ||
3.0 mm 3.0 mm |
UL 746 | ||
阻燃性能 FLAME CHARACTERISTICS |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
阻燃等级 Flame retardant level |
UL 94 | ||
0.75 mm 0.75 mm |
UL 94 | ||
1.50 mm 1.50 mm |
UL 94 | ||
3.00 mm 3.00 mm |
UL 94 | ||
灼热丝可燃性指数 Glowing wire flammability index |
IEC 60695-2-12 | ||
0.75 mm 0.75 mm |
℃ | IEC 60695-2-12 | |
1.5 mm 1.5 mm |
℃ | IEC 60695-2-12 | |
3.0 mm 3.0 mm |
℃ | IEC 60695-2-12 | |
灼热丝起燃温度 Igniting temperature of the hot wire |
IEC 60695-2-13 | ||
0.75 mm 0.75 mm |
℃ | IEC 60695-2-13 | |
1.5 mm 1.5 mm |
℃ | IEC 60695-2-13 | |
3 mm 3 mm |
℃ | IEC 60695-2-13 | |
极限氧指数 Extreme oxygen index |
% | ISO 4589-2 |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
【新闻资讯】查看全部
科技创新:3M采用玻璃微珠消费农用塑膜
2016-05-10 3M公司应用开发工程师Fernando Cervantes在2016墨西哥国际橡塑展上说,玻璃微珠可使生产商用相同数量的树脂材料生产出更多的低密度和线性低密度塑料薄膜。 玻璃微珠还可增加薄膜的白度,用于替代钛白粉。这种材料可大面积扩大光照,有利于作物的生长。 微珠薄膜的开发始于去年。位于美国明尼苏达州圣保罗的3M公司目前正与薄膜生产商合作,着手开发新应用。 3M于2013年在墨西哥圣路易波托斯开设了创新中心。3M自1947年起就在墨西哥经营, |
科技创新:3M采用玻璃微珠消费农用塑膜 3M公司运用研发工程师Fernando Cervantes在2016墨西哥国际性橡塑展上说,玻璃微珠可使制造商用同样总数的复合树脂生产制造出大量的密度低和线形密度低塑胶薄膜。 玻璃微珠还可提升薄膜的细度,用以取代聚乙烯蜡。这类原材料可大规模扩张阳光照射,有益于农作物的生长发育。 微珠薄膜的开发设计起源于上年。坐落于英国阿肯色州佛罗伦萨的3M公司现阶段正与薄膜制造商协作,下手开发运用。 3M于2013年在墨西哥圣路易波托斯设立了创新中心。3M自1947年起就在墨西哥运营,现有职工约7000名。 3M微珠还用以生产制造车体面板,这类面板上年11月得到塑胶技术工程师研究会轿车联合会的巨奖。通用汽车公司公司选用内地构造塑件(CSP)公司出示的热塑性树脂生产制造车体面板,得到该荣誉奖。CSP坐落于得克萨斯州奥本山,公司选用中空玻璃微珠和特有的表层工艺处理取代碳酸氢钙,与规范原材料对比,这类原材料最少减脂28%。 来源于:慧聪胶网 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |
价格走势图
开始时间:
结束时间:
材料厂家:
【牌号齐全,内容全面】
全网共2500+项牌号+上游原料单体+原油价格,最长可追溯近20年价格行情
【精准,及时,权威!】
专业团队挖掘行情信息,第一时间发布行情
抱歉!该牌号暂无认证数据。
免责声明:参考价格是搜料网根据网络大数据拟合分析的结果,仅供参考。实际成交价取决但不限于以下因素:下单时间,付款方式,交货方式,数量,税费,色号,产地,项目信息。
- 太阳能光伏组件
- 2019-03-14 190
- 应用行业:电气电子 应用市场:太阳能电池 终端客户:不明 产品名称:光伏组件 选材要求:1-UV稳定性好 2-耐候性、耐化学性好 3-延展
- 阅读全文
太阳能光伏组件
1- Vydyne® 25WSP是一种黑色耐候注塑成型级PA66树脂,具有强度高、刚性好、韧性好、熔点高、表面润滑性好、耐磨性好等工程性能的良好平衡组合
2-Vydyne® 25WSP保持了PA66对许多化学品、机器和机油、溶剂和汽油的典型耐化学性
2-Vydyne® 25WSP保持了PA66对许多化学品、机器和机油、溶剂和汽油的典型耐化学性
3-Vydyne® 25WSP提供了非常好的流动性和易成型性。典型应用包括电缆扎带/扎带,其中其易于流动、良好延展性和高拉伸强度的组合尤其具有吸引力,以及各种需要耐候性的电气/电子和其他应用
收起
抱歉!暂无数据。