牌号简介 About |
---|
氧化铝陶瓷珠填充环氧树脂系统,在恶劣的使用条件下具有优异的耐磨性和耐磨性。快速固化允许维修后的加工设备在2小时内恢复使用。预期用途:维修洗涤器、除灰系统、管道弯头、筛网、斜槽、削片机、料仓、漏斗、料仓、分离器和消化台。保护抽风机、洗衣机、外壳风扇、破碎机、断路器和传送带螺钉。产品特点:快速固化,停机时间短,耐磨损,能承受各种化学品的冲击,无下垂。 Alumina ceramic bead-filled epoxy system with outstanding wear and abrasion resistance for severe service conditions. Fast cure allows for repaired processing equipment to be returned to service in as little as 2 hours. Intended Use: Repair scrubbers, ash handling systems, pipe elbows, screens, chutes, chippers, bins, hoppers, bunkers, separators and digester tables. Protect exhausters, launderers, housing fans, crushers, breakers, and conveyor screws. Product Features: Fast cure for minimal downtime Superior wear and abrasion resistance Able to withstand impact Resistant to a wide range of chemicals Non-sagging |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
2.00 | g/cm³ | |
特定体积 Specific volume |
0.499 | cm³/g | |
收缩率 Shrinkage rate |
|||
MD MD |
0.080 | % | ASTM D2566 |
固体含量 Solid content |
|||
by Volume by Volume |
100 | % | |
电气性能 Electrical performance |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
介电常数 Dielectric constant |
45.0 | ASTM D150 | |
补充信息 Supplementary information |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
耐热温度 Heat resistant temperature |
|||
Dry Dry |
℃ | ||
Wet Wet |
℃ | ||
拉伸剪切强度 Tensile shear strength |
MPa | ASTM D1002 | |
memo_intro memo_intro |
|||
Uncured Properties Uncured Properties |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
固化时间 Curing time |
hr | ||
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
邵氏硬度 Shore hardness |
|||
邵氏 D Shaw's D |
ASTM D2240 | ||
弯曲强度 bending strength |
MPa | ASTM D790 | |
压缩强度 compressive strength |
MPa | ASTM D695 | |
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
线性热膨胀系数 Linear coefficient of thermal expansion |
|||
MD MD |
1/℃ | ASTM D696 | |
热固组件 Thermosetting components |
|||
部件 A Component A |
|||
部件 B Component B |
|||
储存稳定性 storage stability |
|||
24 ℃ 24 ℃ |
min |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
【新闻资讯】查看全部
3D打印给注塑产品带来的附加价值
2016-05-05 对于模具制造商来说,由于模具的质量直接决定了注塑生产效率,并决定产品质量,从而决定产品附加值,所以,如何在最小周期时间内高效冷却塑料产品,成为随形冷却模具设计与制造过程中关键的考量因素,而冷却在这其间扮演了重要的角色。 < |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |