3D打印材料，ALKAMIX™ MB-SAMBA对比3D打印材料，ALKAMIX™ MB-AO300物性表,价格行情_搜料

牌号信息	ALKAMIX™ MB-SAMBA 物性表 3D打印材料 & 澳大利亚凯诺斯指导价格：暂无塑料库存：缺货	ALKAMIX™ MB-AO300 物性表 3D打印材料 & 澳大利亚凯诺斯指导价格：暂无塑料库存：缺货
牌号简介	ALKAMIX™ MB-SAMBA是一种以2%的浓度用芥酸酰胺配制的卡瓦母粒。挤出过程中可向聚乙烯中加入ALKAMIX™ MB-SAMBA，以降低薄膜的摩擦系数。所需的水平将根据所需的摩擦系数、薄膜厚度、聚合物类型（LLDPE、LDPE等）和其他因素（如存在其他添加剂（包括防结块、着色剂/颜料等）而变化。对于注塑制品，由于注塑制品的厚度，建议MB-Samba的典型添加率高达2.0%。较高的添加率可能会导致印刷或标签粘附问题，或可能出现翘曲。根据良好生产规范和确保符合美国食品和药品管理局法规CFR21要求的最大添加量ALKAMIX™ MB-SAMBA是达到预期效果所需的最小添加量。当添加到不含任何滑动添加剂的聚乙烯配方中时，建议的最大含量为10%。转换器必须对使用该材料作为部件制造的成品的适用性以及对给定限制的遵守情况进行验证，以确保符合所有相关法规。整体迁移限制可适用于成品。 ALKAMIX™ MB-SAMBA is a slip masterbatch formulated with Erucamide at a concentration of 2%. ALKAMIX™ MB-SAMBA can be added to polyethylene during extrusion to reduce the coefficient of friction of films. The level required will vary according to coefficient of friction desired, gauge of film, polymer type (LLDPE,LDPE, etc…) and other factors such as the presence of other additives (including antiblocks, colourants / pigments, etc...). For injection moulded articles, typical addition rates of MB-SAMBA of up to 2.0% are recommended due to the thickness of the moulded article. Higher addition rates may result in problems with printing or label adhesion, or possibly warpage. The maximum level of addition of ALKAMIX™ MB-SAMBA based on both good manufacturing practice and to ensure conformance to the requirements to the United States Food and Drug Administration Regulations CFR21 is the minimum required to achieve the desired effect. When added to a polyethylene formulation free of any slip additives, the maximum recommended level is 10%. The suitability of finished articles manufactured using this material as a component, and the observance of given limitations, must be verified by the converter for each application to ensure compliance with all relevant regulations. An overall migration limit may apply to the finished article.	ALKAMIX™ MB-AO300是不含BHT（丁基化羟基甲苯）的抗氧剂母粒，设计用于在挤出过程中赋予基层低密度聚乙烯热加工稳定性。ALKAMIX™ MB-AO300可在挤出过程中添加到基层低密度聚乙烯中，以帮助克服热不稳定性问题。所需的水平将根据挤出类型、条件和所用聚合物的不同而变化，但是建议的添加水平在1%到2%之间。ALKAMIX™ MB-AO300也可用作停堆化合物，以防止聚合物在挤出机中被闲置氧化。作为一种停堆化合物，它通常以30%或更多的浓度添加到分数MFI低密度聚乙烯中。当添加到不含任何其他添加剂的聚乙烯配方中时，根据良好的生产实践和确保符合美国食品药品管理局法规CFR21要求的最大添加量为4%。转换器必须对使用该材料作为部件制造的成品的适用性以及对给定限制的遵守情况进行验证，以确保符合所有相关法规。整体迁移限制可适用于成品。 ALKAMIX™ MB-AO300 is BHT (Butylated Hydroxy Toluene) free antioxidant masterbatch designed to impart thermal processing stability to base grade low density polyethylene during extrusion. ALKAMIX™ MB-AO300 can be added to base grade low density polyethylene during extrusion to assist in overcoming thermal instability problems. The level required will vary according to the type of extrusion, conditions and polymer used, however the recommended addition level is between 1 and 2 percent. ALKAMIX™ MB-AO300 can also be used as a shutdown compound to prevent oxidation of polymer left idle in an extruder. As a shutdown compound, it is usually added at concentrations of 30 percent or more to fractional MFI low density polyethylenes. The maximum level of addition of ALKAMIX™MB-AO300 based on both good manufacturing practice and to ensure conformance to the requirements to the United States Food and Drug Administration Regulations CFR21 is 4 percent, when added to a polyethylene formulation free of any other additives. The suitability of finished articles manufactured using this material as a component, and the observance of given limitations, must be verified by the converter for each application to ensure compliance with all relevant regulations. An overall migration limit may apply to the finished article.

产品描述
厂家：	澳大利亚凯诺斯 Qenos	澳大利亚凯诺斯 Qenos
类别：	3D打印材料 3D打印材料	3D打印材料 3D打印材料
填料：
用途：	母料	母料
性能特点：	高光滑性 Smoothness	抗氧化 Inoxidizability
加工条件：